General Features

• External transmitters or signal conditioners can be eliminated by direct connection of the sensor output to more than 38 Plug-in Input Signal Conditioners that include:
  – AC/DC Current – Pressure – Resistance
  – AC/DC Voltage – Process – *Temperature
  – Load Cell – Prototype – 4 to 20 mA
  *See model BL-40H and DL-40H for higher accuracy digitally linearized thermocouple and RTD
  
• Optional isolated 16 bit analog output. User or factory scalable to 4 to 20 mA, 0 to 20 mA or 0 to 10 V across any desired digital span from ± one count to the full scale range of – 1999 to 9999 (12000 counts).
  
• Auto-sensing AC/DC power supply. For voltages between
  85-265 V AC / 95-370 V DC (PS1) or 18-48 V AC / 10-72 V DC (PS2).
  
• 24 V DC excitation is available to power external transmitters and 5 or 10 V DC excitation is available for resistance bridge type sensors such as Load Cells and Pressure Transducers.
  
• Standard red or optional green or super bright red 4-digit LED with display range –1999 to 9999 (12000 counts).
  
• Three annunciator LEDs provide front panel alarm status indication for up to three setpoints.
  
• One 10 Amp Form C and one 5 Amp Form A relay, or up to three 5 Amp Form A are available.
  
• When analog output is installed, one 10 A Form C or two 5 A Form A relays can be supported.
  
• Automatic intelligent averaging smoothes noisy signals, while providing a fast display response to real level changes.

Software Features

Three-button front panel programming of;

• Decimal point setting.
  
• Four-level brightness control of digital display.
  
• Peak and valley view and reset.
  
• Three programmable setpoints.
  
• Adjustable delay-on-make and delay-on-break time for setpoints 1 and 2.
  
• Relay activation can be selected to occur above (HI) or below (LO) each setpoint.
  
• Hysteresis setting for all three setpoints (if three relays are installed).

Input Module Compatibility

LYNX FAMILY: Accepts more than 24 different Plug-in I-Series Input Signal Conditioners approved for Texmate’s Lynx Family of meters.

Specifications

• Input Specs: ...... Depends on input signal conditioner
  
• A/D Converter: ...... 14 bit single slope
  
• Accuracy: ...... ±(0.05% of reading + 2 counts)
  
• Temp. Coeff.: ...... 100 ppm/°C (Typical)
  
• Warm up time: ...... 2 minutes
  
• Conversion Rate: ...... 5 conversions per second (Typical)
  
• Display: ...... 4 digit 0.56" Red LED display (std), 0.56” Red, Green or Super Bright Red (optn). Range –1999 to 9999 counts.
  
• Polarity: ...... Assumed positive. Displays – negative
  
• Decimal Selection: ...... Front panel button selectable, X•X•X•X•
  
• Positive Overrange: ...... Top segments of digital display flash
  
• Negative Overrange: ...... Bottom segment of digital display flash
  
• Relay Output: ...... Three 5 A Form A relays or one 10 A Form C, and one 5 A Form A relay.
  
• Analog Output: ...... Isolated 16 bit user scalable mA or V
  OIC (mA out) 4-20 mA @ 0 to 500 ohms max loop resistance
  OIV (volts out) 0-10 V DC @ 500 ohms or higher resistance
  
• Power Supply: ...... AC/DC Auto sensing wide range supply
  PS1 (std) 85-265 VAC / 95-370 VDC @ 2.5W max 3.2W
  PS2 18-48 VAC / 10-72 VDC @ 2.5W max 3.2W
  
• Operating Temp.: ...... 0 to 60 °C
  
• Storage Temp: ...... –20 °C to 70 °C.
  
• Relative Humidity: ...... 95% (non condensing)
  
• Case Dimensions: ...... 1/16 DIN (Bezel 96Wx24H mm)
  Depth behind bezel (4.81") 122.2mm
  Plus (0.5”) 12.7mm for connectors
  
• Weight: ...... 7 oz., 9 oz when packed